The best options we have to fight off sway on your 2020 Holiday Rambler Vacationer (Ford - 26,000 GVWR) are an anti rear sway bar followed by jounce spring upgrades. The combination of these parts will help drastically with sway, body roll, and overall stability/handling. If you were only to do one, I recommend the rear anti-sway as you will see the biggest improvement from this alone.
Roadmaster Rear Anti-Sway Bar part # RM-1139-149
SumoSprings Rebel Custom Helper Springs part # SSF-173-40-2
SumoSprings... view full answer...
I suggest the Adco Olefin HD All-Climate RV Cover for Class A Motorhomes, # AD74ZR. This is for Class A motorhomes up to 37 feet. The, # AD64ZR is for up to 34 feet and will work just fine with the attached ladder but if you have need extra fabric due to a satellite dish, then the 37 foot # AD74ZR may be a better option. Each option has cinch ropes at front and rear of cover to remove slack. view full answer...
Since the landing gear feet of your 2019 Holiday Rambler Navigator 37R are 10 inches and round the correct set of SnapPads would be the part # SP64FR74 that you referenced. view full answer...
We've had this question come up before and here's what Roadmaster sent me in response:
The axle bracket can be located on either the driver or passenger side and the tie rod bracket (B802) can be located on top or bottom side of the tie rod.
Orientation of the shock is not important, the unit can have the spring pointed towards the center of the RV or out towards the tire. Similarly, the eyelets on the shock unit (where bolts hold it to the brackets) can be located on both the top or... view full answer...
There isn't a person or company we are aware of that can repair circuit boards that we recommend people go to. If your Power Gear Keypad # LC82FR is damaged then easiest solution would be to go with a new one but you might get lucky if you can find someone near you who works on electronics as they might have a solution. Or they might tell you it's damaged to point it would just need to be replaced. view full answer...
We do have a large selection of RV water tanks currently available. In order to choose the correct tank, I recommend simply taking a few measurements on your existing tank or on the space you have available for one. Our available tanks from Valterra all feature an 8 inch width and 16 inch height, but vary in their lengths and capacities.
For example, the Valterra RV Water Tank # RB042 measures 42 inches long and has a 21 gallon capacity. This is a really nice option for storing fresh... view full answer...
Yes, since your 2019 Holiday Rambler Vacationer 35P is built on the Ford F-53 chassis and it has a GVWR of 24,000 pounds the Roadmaster Reflex Steering Stabilizer # RM-RBK25-RSSA you referenced is the correct kit and it will work perfectly. This will do a great job of keeping the RV in line during travel by mounting between the steering mechanism and chassis and constantly working to maintain its position.
All the custom mounting brackets are included. I have attached a short video demonstration... view full answer...
To convert your separate brake light wiring on your RV to the combined signal needed for your RV trailer connector plug, I recommend the Roadmaster Brite-Lite Wiring Converter # RM-732. This will combine your turn and stop on the left and right sides to make it compatible with trailer connectors on the vehicle side of the connection.
If I misunderstood and your tow dolly needs the wires separated for separate brake and turn, then you will want the Vehicle to Vehicle Tail Light Converter... view full answer...
For your 2004 Holiday Rambler Endeavor, I recommend you use a 7-way instead of a 6-way and get a connector like the 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring - Vehicle End # HM40975-11998. This kit will give you the trailer connector, the mount, the butt connectors and the ring terminal for installation.
The wiring of this trailer connection is as follows and I recommend using a circuit tester like # PTW2993 to ensure you match function to function on... view full answer...
If you have air brakes on your motorhome, you can use the Hayes Air Actuated Trailer Brake Controller # HA100400C you were looking at. This will use the air pressure to determine the correct braking force for the tow dolly. If you do not have air brakes I have two additional options.
The first is the Redarc Tow-Pro Liberty Brake Controller # RED52VR. This is a low profile option where the main unit mounts out of sight so only the control knob is visible. The knob controls the brake power... view full answer...
You can easily replace the thermostatically controlled RV ceiling fan you have in your 1999 Holiday Rambler Endeavor 37WDS with one that does not have that feature. We have the Ventline Ventadome Trailer Roof Vent part # V2094SP-28 which fits the standard 14 inch by 14 inch rough cut RV roof opening and has a fan without a thermostat. view full answer...
So there is a single option available for a bike rack that is approved for use on an RV (both a motorhome like yours and a trailer should you have one or go that route in the future) and has the ability to carry four 60 lb electric bikes, which is from Let's Go Aero. It is actually a 2-bike rack with an add-on, so what you will need is the following:
- Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes # LGA77FR
- 2-Bike Add-On for Lets Go Aero V-Lectric Electric Bike Rack... view full answer...
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Bulldog Tandem Landing Gear Set # BD500162. Either way this landing gear set would work well for you, you just might have to have the brackets of your trailer removed and then install the brackets of the #... view full answer...
Your 2019 Holiday Rambler Admiral RV does have a plug under the dash. My recommendation for you is to use the Redarc Tow Pro Elite # RED44FR and the wiring harness # RED87FR. This will plug right in and will also give you a nice clean look on your dash. view full answer...
Yes it does sound like the control module of your Lippert RV steps is having issues which is causing the problem you are having and the replacement would then be the part # LC301702 that you referenced. view full answer...
The Atwood Air Command Rooftop RV Air Conditioner part # AT15028-22 comes with everything you will need to install on your 2007 Holiday Rambler Toy Hauler. There will not be an additional wiring or base plates needed. It comes with the wiring harness for the thermostat as well as for the unit itself. The hardware to attach the unit to your roof is also included for you as well as all the foam gaskets and vent covers etc. view full answer...
Yes, if you were looking to replace the PD9155 in your RV the part # PD9160A would fit and work well. It provides the same function of converting 120 volt power to 12 volt power up to 60 amps. view full answer...
For your 2009 Holiday Rambler Endeavor the Atwood AC Unit part # AT15028-22 would be a great option that will work well. It's ducted so it will fit right to your motorhome, it is rated at 15k btu so it has great cooling capacities, and it has a heat pump like you need as well. The drain system of this unit will match what you have on your motorhome as well. view full answer...
Go To Results